#BEDFORD CFS FULL#
#BEDFORD CFS SERIES#

In addition to these, larger trucks and bus chassis were also sold, albeit in small numbers. Isuzu KA 40/41, KS, KT, TLD and TLG trucks were offered in the light-duty range, and the JBR, JCR, JCS, SBR and SCR in the medium-duty range. Isuzu went on to dominate the Australian truck market.

GMH made good decisions in those days and the introduction of the Isuzu products was timely. Introduced to Australia by General Motors Holden (GMH) in 1972, Isuzu trucks were initially marketed as вЂBedford by IsuzuвЂ™, which helped appeal to an audience unfamiliar with the brand by promoting buyer confidence via association with Bedford. In Australia, the TK could be optioned with Holden 253 or 308 petrol V8 power and the KM had a two-stroke 6V53 Detroit Diesel/ Roadranger transmission option. The Bedford KM used the same cab, but with a slightly restyled front end and was marketed for heavier-duty applications than the TK: 16В tons and over. The Bedford TK range replaced the S in 1959, but the RL continued in production until 1969, when it was replaced by the M Series.

#BEDFORD CFS SERIES#

The A Series was updated in 1957 and became the J Series. In 1953, the Bedford A series, bonneted range was released, with numbers 2, 3, 4 and 5 denoting the weight rating. The very popular CA was replaced by the CF in 1969 and Australian CFs came with a Holden six-cylinder engine.ДЄt the same time came the sub-nosed, seven-ton S Series and the SB bus chassis. In 1952, Bedford released the semi-bonneted CA van, with 1.5-litre petrol power, or Perkins diesel option. The pre-war K, M and O trucks continued in production, beside newer models, until 1953. Many of the WWII Bedfords remained in service post-War and those that were pensioned off went into civilian roles. Some were fitted with armoured bodywork.ДЄ larger, 4Г—4, forward-control QL model вЂ“ dubbed the Queen Lizzie вЂ“ went into service in 1941. The K, M and O Series trucks were redesigned for military use, by fitting a wider, flat-fronted, sloping bonnet and were designated OX and OY series. Also launched was a new JC 1/2-3/4-ton van. The new range consisted of the K (1 1/2-2-tons), MS and ML (2вЂ“3В tons), OS and OL (3вЂ“4В tons), OS/40 and OL/40 (5В tons) series, and the OB bus.

#BEDFORD CFS FULL#

In 1935, Bedford began work on a 3/4-ton MW truck for the British Army and it entered service in 1939.ДЄ full range of new Bedford civilian models were released in mid-1939, three months before the outbreak of Word War Two. The new releases continued in 1934, with the introduction of the three-ton WT Series, followed by a bus version the following year. In the following year a WS 1.5-tonner, a VYC 3/4-ton light van and car-based AS vans were launched. The first Bedford-only-branded WHG and WLG two-ton trucks and bus chassis were released in 1931, powered by the proved overhead-valve, six-cylinder Chevrolet Stove Bolt 6 engine. Interestingly, this double-branding occurred again, in 1972, when Isuzus replaced Bedfords in Australia. The first Bedford AC and LQ 3/4-ton van, ambulance and small bus models were produced at Luton from 1929 to 1931, branded вЂChevrolet BedfordвЂ™. Before that time, GM imported Canadian-assembled вЂBritish ChevroletsвЂ™ to the UK, but made the decision to produce Vauxhall-designed trucks in Bedfordshire. Bedford was a relative late-comer to the truck business, springing to life after General Motors (USA) purchased Vauxhall Motors in 1925.

Bedford cfs